Jefferson Series with Oiled Butcher Block Top

Lead Time: Green 1-3 Days, Orange 3-5 Days, Black 5-10 Days.
Large & custom orders take slightly longer.

The Solid Maple Butcherblock tops used by BenchProâ„¢ are made from 1-3/4 thick strips of genuine Maple Hardwood. To prevent warpage and splitting, the wood is died in a low-heat atmosphere for almost one year before it is cut into strips and glued edge to edge. The hardwood strips vary in width, so that some strips are single and some strips are double wide. This gives the tops added strength while reducing the possibility of the top splitting along its seams.

We generally stock over 500 Maple Butcherblock tops, ready for assembly. We receive unfinished tops in truckload quantities direct from the mill. We first size and sand them, then round the edges, and then surface them in either an oiled or lacquered finish. (While lacquer finished tops have a nicer appearance for offices, the less expensive oiled finish is generally best for production and high use areas, as they can be resurfaced easily, and minor damage does not affect their appearance).

Note: Although our tops and shelves are very water resistant, they are not recommended for use where running water is present or where constant water spills are possible. These type of wet applications require 100% stainless steel tables which are available from lab and kitchen suppliers.

Note: Jefferson tables are built standard at 30". If you wish a higher or lower table, prices will be adjusted as shown below.

These benches come with ergonomic contoured front edges. These allow the operator to lay their arm across the edge without discontfort.

Add 12% for lacquered tops.

Lead Time: Green 1-3 Days, Orange 3-5 Days, Black 5-10 Days.
Large & custom orders take slightly longer.

The Solid Maple Butcherblock tops used by BenchProâ„¢ are made from 1-3/4 thick strips of genuine Maple Hardwood. To prevent warpage and splitting, the wood is died in a low-heat atmosphere for almost one year before it is cut into strips and glued edge to edge. The hardwood strips vary in width, so that some strips are single and some strips are double wide. This gives the tops added strength while reducing the possibility of the top splitting along its seams.

We generally stock over 500 Maple Butcherblock tops, ready for assembly. We receive unfinished tops in truckload quantities direct from the mill. We first size and sand them, then round the edges, and then surface them in either an oiled or lacquered finish. (While lacquer finished tops have a nicer appearance for offices, the less expensive oiled finish is generally best for production and high use areas, as they can be resurfaced easily, and minor damage does not affect their appearance).

Note: Although our tops and shelves are very water resistant, they are not recommended for use where running water is present or where constant water spills are possible. These type of wet applications require 100% stainless steel tables which are available from lab and kitchen suppliers.

Note: Jefferson tables are built standard at 30". If you wish a higher or lower table, prices will be adjusted as shown below.

These benches come with ergonomic contoured front edges. These allow the operator to lay their arm across the edge without discontfort.

Add 12% for lacquered tops.

Lead Time: Green 1-3 Days, Orange 3-5 Days, Black 5-10 Days.
Large & custom orders take slightly longer.

The Solid Maple Butcherblock tops used by BenchProâ„¢ are made from 1-3/4 thick strips of genuine Maple Hardwood. To prevent warpage and splitting, the wood is died in a low-heat atmosphere for almost one year before it is cut into strips and glued edge to edge. The hardwood strips vary in width, so that some strips are single and some strips are double wide. This gives the tops added strength while reducing the possibility of the top splitting along its seams.

We generally stock over 500 Maple Butcherblock tops, ready for assembly. We receive unfinished tops in truckload quantities direct from the mill. We first size and sand them, then round the edges, and then surface them in either an oiled or lacquered finish. (While lacquer finished tops have a nicer appearance for offices, the less expensive oiled finish is generally best for production and high use areas, as they can be resurfaced easily, and minor damage does not affect their appearance).

Note: Although our tops and shelves are very water resistant, they are not recommended for use where running water is present or where constant water spills are possible. These type of wet applications require 100% stainless steel tables which are available from lab and kitchen suppliers.

Note: Jefferson tables are built standard at 30". If you wish a higher or lower table, prices will be adjusted as shown below.

These benches come with ergonomic contoured front edges. These allow the operator to lay their arm across the edge without discontfort.

Add 12% for lacquered tops.